Its starts at the source! modifying your audio appliances!
By far the easiest modification is adapting your existing interconnectors to Brenda'sTM. Either fully made up from Bocchino Audio or just the BrendaTM component so that you can use your existing interconnect wire or the interconnect wire of your choice. Installing interconnect wires into the BrendaTM is easier and safer than soldering wires onto standard RCA interconnector connector components.
Most people with audio / stereo equipment have two principal sources of music. Either the Turntable or the CD player. Today there are also a video, DAT, cassette and computer sources. For the purpose of this exercise I will concentrate only on the Turntable and CD.
Starting at the source, replace the installed RCA chassis receptors on the Turntable and CD player with TomCatsTM. If you have separate CD transport and DAC then replace all the RCA chassis connectors with TomCatsTM . Similarly, with a Turntable , if there are more connection interfaces than just the single route from the Turntable to the pre-amp ( such as going through a step-up device for a Moving Coil cartridge or having a separate phono pre-amplifier that is used to step up the voltage for a line-source pre-amplifier these interfaces also need to have their standard RCA connectors replaced with TomCatsTM ). On the pre-amp replace the input sockets with TomCatsTM. Most pre-amplifiers today are slim line and not suitable for the spacing distances required to accommodate TomCatsTM. Some further modifications may be required here. TomCatsTM are required for the Turntable , CD and any other source inputs ( that you want to modify ) and for the pre-amp output to the Power-amp.
At the Power-amp, TomCatsTM are installed to convey the signal into the power-amp. If possible WireGrubsTM are used to secure the input wire to the Power-amp input circuit.
If you are able to, then the installation of MinMin-LightsTM will deliver a performance beyond anything else available anywhere today as an interconnector system
At the amplifier output install Monopoles®. At the loudspeaker input install Monopoles®. If possible, the crossover has been rebuilt using WireGrubsTM. Also, if possible, the loudspeaker transducer terminals can be replaced with WireTailsTM. And the loudspeaker transducer mounting screws can be replaced with '316' Stainless Steel bolts and CaneToadsTM so holding the loudspeaker transducers more securely onto the front panel.
To connect the amplifier to the Speakers use either FM2 or FM3 Spade Lugs on your choice of quality audio cable or Bocchino Audio B.A.S.S. StraightTM Speaker Cable.
The electronic appliances and loudspeakers have been placed on MonofeetTM and the Turntable is able to accommodate a suitable MonomassTM ; Or any other suitable record stabilizer. Your CD, Turntable and Speakers isolated with Bocchino Audio Isolation Platforms or equivalent.
Loudspeakers, if you don't have any, either the Panda Model 10 or any of the other PandaTM designs to choose from. All in your own Concert-RoomTM.
So do you really need it all. Yes!
The resulting quality of the reproduction of music is not attainable through any appliance 'up-grade'. An appliance up-grade will still have soldered outputs. It will still cloak the signal with a choking grip and though the quality of reproduction gets better with the more expensive audio appliances ( not necessarily the true rule of thumb but generally a trend ) these are still locked into the mass-assembly manufacturing practices of 'soldering everything'.
One audio appliance that shows the greatest benefit from utilizing Bocchino Audio Components is the humble turntable. Current levels from low output moving coils are soon defeated by the presence of solder.
Bocchino Audio bare-wire components at the critical signal transfer interfaces allow the music to flow freely. The result is a quality of reproduction where intimacy and the stereo-holographic-focal-field takes on a level of realism only bettered by the actual live performance itself.
Bocchino Audio components are designed to be the best possible topology from a scientific / engineering perspective. They do their job better than any other equivalent component available today; anywhere in the world today.
Bocchino Audio Components are easily adaptable to most existing audio appliances. Using Bocchino Audio Components on existing audio appliances may obviate the need to upgrade your appliance to a more expensive equivalent as it will result in your existing appliance sounding better than any upgrade could possibly have offered. In fact the scale of the quality of reproduction places the new performance of your existing component in a different dimension category than a normal upgrade would have delivered. The installation of Bocchino Audio Components will also result in improving the re-sale / upgrade value of your appliance due to the improvement that this type of upgrade / modification delivers.
Before buying your New Audio Appliances ask the vendor / retailer to arrange for the manufacturer to install those Bocchino Audio Components you desire. I'm yet to have any manufacturer reject a modification to install any of my components that have been requested by clients in order to have the sale. All those manufacturers that have installed my audio components in their appliances recommend to their clients to seriously consider installing them.
Most manufacturers have 'formulae' for calculating their sale price of their components. The high fabrication cost and subsequent sale price of Bocchino Audio Components is seen as prohibitive by many manufacturers. The installation of a single $100.00 component into an appliance at the production level may result in a price increase of up to $600.00 at the retail level. To garner an equivalent leap in value, you, the end user, can save a bundle by supplying the manufacturer your Bocchino Audio Component and so effectively gain an upgrade equivalent to greater than six times the value of the components installed.
When installing Bocchino Audio Components onto an existing audio appliance contact a suitably qualified electrical professional. Do not do it yourself. Unless you are an engineer or similarly qualified professional.
Bocchino Audio components are most adept to the needs of the DIY audio enthusiast. They will enable a maximization of the performance of any audio component into which they are incorporated.
If your dealer is too reticent or lazy to meet your requests contact me, my local agent or go to another dealer. I can point you in the right direction in almost any country. Or even do it here in Australia for you.
All clients that have installed Bocchino Audio Components are surprised at the enormous magnitude of improvement and enjoyment of their music.
A 100% satisfaction rate.
Enjoy!